Ultrasonic cleaning machine is a kind of equipment specially used for cleaning bottles. It is highly automated and suitable for clean cleaning of 10-30 ml oral liquid glass bottles that meet the requirements of YY0056. The machine automatically completes the complete production process from bottle feeding, ultrasonic rough washing, fine washing on the outer wall of the bottle, and fine washing from the inner wall of the bottle to the bottle. The combination of ultrasonic cleaning and water-air pressure jet cleaning is a good cleaning equipment for the popular and clean bottle-washing degree. The washing bottle has high clarity and low crushing rate.
The equipment mainly uses the principle of ultrasonic cavitation, the ultrasonic wave propagates in the liquid, and the ultrasonic field is subjected to strong compression and stretching, resulting in cavity and cavitation. When the bubbles formed by the ultrasonic waves suddenly rupture, more than 1000 atmospheric pressures can be generated. This constant generation of intense micro-blasting and shock waves instead of manual washing can greatly reduce the adhesion of dirt, and can cause the dirt on the surface of the object to be cleaned to be destroyed and quickly fall off.
The condensate removal of the heater of the bottle washer is not smooth, which may cause difficulty in heating. It is necessary to open the bypass valve of the steam trap to remove the condensed water. If the steam supply pipe is too long, the bottle washer will not be well insulated, and it will be difficult to remove too much condensed water. It is necessary to improve the insulation layer of the steam pipe. If the heater is too thick, it will also affect heat transfer, so it is necessary to clean the scale regularly.
In addition, after cleaning the filter in the drain box, remember to install it. The quick drain valve can be drained and drained before cleaning the filter. Open the butterfly valve to discharge the pre-soaking solution, open the pre-soaking tank cleaning hole cover, and rinse the glass debris passage with high-pressure water. Then open the shut-off valve, rinse the warm water tank and the hot water tank separately with clean water, rinse off and close the shut-off valve and the clean water main valve. Need to be reminded that the debris, dirt, glass fragments, etc. around the instrument should be cleaned up. Finally, don't forget to clean the bottle area, close the quick-discharge valve, and fill the device with oil.
The operation of the ultrasonic bottle washing equipment is done by the cooperation of the various components, and as long as one component has problems, it cannot work normally. In this regard, some manufacturers have suggested that if the drive chain of the bottle washer is too loose and the transmission force has a problem caused by the impact of the clutch, it is necessary to tighten the drive chain; if the clutch is loose due to the loosening of the pressure plate, it is necessary Tighten bolts, screws, and apply anti-loosening agent.
The above is for everyone to share today, about the daily maintenance and precautions of the ultrasonic bottle washer , I hope this article can help everyone.
The equipment mainly uses the principle of ultrasonic cavitation, the ultrasonic wave propagates in the liquid, and the ultrasonic field is subjected to strong compression and stretching, resulting in cavity and cavitation. When the bubbles formed by the ultrasonic waves suddenly rupture, more than 1000 atmospheric pressures can be generated. This constant generation of intense micro-blasting and shock waves instead of manual washing can greatly reduce the adhesion of dirt, and can cause the dirt on the surface of the object to be cleaned to be destroyed and quickly fall off.
The condensate removal of the heater of the bottle washer is not smooth, which may cause difficulty in heating. It is necessary to open the bypass valve of the steam trap to remove the condensed water. If the steam supply pipe is too long, the bottle washer will not be well insulated, and it will be difficult to remove too much condensed water. It is necessary to improve the insulation layer of the steam pipe. If the heater is too thick, it will also affect heat transfer, so it is necessary to clean the scale regularly.
In addition, after cleaning the filter in the drain box, remember to install it. The quick drain valve can be drained and drained before cleaning the filter. Open the butterfly valve to discharge the pre-soaking solution, open the pre-soaking tank cleaning hole cover, and rinse the glass debris passage with high-pressure water. Then open the shut-off valve, rinse the warm water tank and the hot water tank separately with clean water, rinse off and close the shut-off valve and the clean water main valve. Need to be reminded that the debris, dirt, glass fragments, etc. around the instrument should be cleaned up. Finally, don't forget to clean the bottle area, close the quick-discharge valve, and fill the device with oil.
The operation of the ultrasonic bottle washing equipment is done by the cooperation of the various components, and as long as one component has problems, it cannot work normally. In this regard, some manufacturers have suggested that if the drive chain of the bottle washer is too loose and the transmission force has a problem caused by the impact of the clutch, it is necessary to tighten the drive chain; if the clutch is loose due to the loosening of the pressure plate, it is necessary Tighten bolts, screws, and apply anti-loosening agent.
The above is for everyone to share today, about the daily maintenance and precautions of the ultrasonic bottle washer , I hope this article can help everyone.
Medical Sigmoidoscope Set,Medical Restoscopy Set,Urology Resectoscope Set,Endoscope Cystoscopy Instruments
ZHEJIANG SHENDASIAO MEDICAL INSTRUMENT CO.,LTD. , https://www.shendasiaomed.com